Cog 18 pin 12864 LCD
Chiyambi cha Zamalonda
| Nambala ya Model | Chithunzi cha RXMG-12864Q |
| Kukula Kwawonetsero | 41.8x26.1mm(VA) |
| Mtundu | Mtengo wa STN |
| Wolamulira | ST7565 kapena ofanana |
| Panopa ntchito | <700uA(3.3V) |
| Chiyankhulo | Seri |
| Voltage yogwira ntchito | 3.1-3.5V |
| Onani mayendedwe | 6H |
| Kuwala kwambuyo | Choyera |
| Onetsani mawonekedwe | Stn negative blue |
| Kutentha kwa Ntchito | -10 ~ 60 ℃ |
| kutentha kosungirako | -20-70 ℃ |
| Kugwiritsa ntchito | Khalidwe, kuwonetsera manambala kwa chosindikizira, zida ndi zina zotero |
Zina za 12864 LCD zowonetsera:
Pin Ntchito:
| Pin NO. | Pin Dzina | Pin Kufotokozera |
| 1 | CS1 | Kusankhidwa kwa chip |
| 2 | /CS | |
| 3 | /RST | Bwezerani chizindikiro (H: zachilendo; L:kukhazikitsanso) |
| 4 | SO | |
| 5 | A0 | Kusankha kwa data/malamulo(H/L) |
| 6 | SI | |
| 7 | SCK | Kulowetsa koloko |
| 8 | Chithunzi cha SCLK | |
| 9 | CDA | Kuyika kwa serial data |
| 10 | NC | |
| 11 | VDD | Mphamvu zabwino |
| 12 | LED + | Positive backlight magetsi |
| 13 | VSS | Negative magetsi, pansi |
| 14 | LED- | Negative backlight magetsi |
| 15 | LED- | Negative backlight magetsi |
| 16 | NC | Palibe |
| 17 | LED + | Positive backlight magetsi |
| 18 | NC | Palibe |
Ntchito Zathu
KUSANGALATSA :
| Onetsani | gawo, zithunzi, mawonekedwe a monochrome lcd module & TFT zovomerezeka |
| Onetsani mawonekedwe | TN,STN,FSTN,HTN,transflective,nyezimira,transmissive,yellow wobiriwira,buluu,imvi optional |
| Mtundu wowonetsera | COB, COG, TAB |
| Lcd makulidwe (cm) | 0.11,0.14 |
| makulidwe a backlight (cm) | 2.8,3.0,3.3 |
| Chiyankhulo | Parallel (8bit, 4bit, 16 bit,80mode,68mode), serial(i2c,spi,uart,usb) |
| Wolamulira | Zosankha |
| IC | Kufa kapena kupakidwa mwasankha |
| Hardware kapena mapulogalamu | Onse anavomera |
| Chidziwitso choperekedwa | Onse idear, chitsanzo, chithunzi, kujambula, ntchito Buku ndi zina zotero zili bwino |
1, ndimafunagawo la LCD limawonetsa manambala 8 ndipo kukula kwake ndi 35mm * 70mm…………?
Yankho: Palibe vuto. Choyamba, pls titumizireni pepala lanu lojambula kapena zitsanzo; tidzakudziwitsani zoyenera ngati zili zokhazikika. Kapena tikhoza kusintha kutengera chimodzi mwa izo.
2,gawo la LCD ili ndi zomwe tikufuna, koma ndi zazikulu, kodi muli ndi kukula kochepa?Andipo zowonetsera ziyenera kusinthidwa pang'ono.
Yankho: Kwa gawo la gawo la LCD, ngati mukufuna kusintha kukula kwa autilaini kapena zowonetsera, LCD glass.mould yatsopano ikufunika. Tikudziwitsani za nkhungu
malipiro pambuyo potsimikizira pamene malipiro,tiyamba pepala lojambulira kuti mufufuze.
3, Kuwala kwa module iyi ya LCD ndi yobiriwira,koma Indikufuna blue backlight.
Yankho: palibe vuto, tikhoza kusintha kwa inu.
4, ndikufuna kusintha gawo latsopano la LCD.Cndi inu?
Yankho: Inde, tingathe. Chonde tumizani pepala lanu lojambulira. Ngati simunatero, chonde ndiuzeni kukula kwa chiwonetsero cha LCD, chidziwitso chowonetsera, ngati pakufunika kuwala kwambuyo kapena PCB.
board ndi IC, Tiwunika mtengondikupatseni mtengo posachedwa.
5, Zomwe zimatsogolera nthawi yogwiritsira ntchito zida
Yankho: Masiku 15 mpaka 30 mutatha kujambula chitsimikiziro cha pepala ndi kulipira kwa zida, titha kukuuzani nthawi yeniyeni mukatsimikizira pepala lojambula.
6,Kodi mungatitumizire zitsanzo kuti tiwoneke?
Yankho: Inde,. Zitsanzo zoyitanitsa zilipo
7,Ndi chiyaniNthawi Yotsogolera?
Yankho: Ngati tili ndi katundu wokhazikika, nthawi yotsogola ndi tsiku limodzi mutatha kulipira. Ngati ndiko kupanga kwakukulu kwa apadera, nthawi yotsogola ndi pafupifupi masiku 1530.
Ngati tingathe kumaliza kale, tidzatumizamumadziwa pasadakhale
8 , Kodi mungavomereze njira zolipirira ziti?
Yankho: Panopa timangovomereza T/T.
